JES9860BAB Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Plaistow, NH
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven temperature all over the place
I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Edgewood, WA
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Oven temperature lagging set temperature by almost 100F
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Dallas, TX
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Getting codes and beeping
Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from San Antonio, TX
- Parts Used:
- 12001656
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven would not work
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Gaines, MI
- Parts Used:
- WP74011493
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Old off new on. Received from supplier promptly and at a good price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Dunkirk, NY
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The filter in the grill section of my stove fell apart.
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Medfield, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the original grease filter was worn and falling apart
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosetta R. from Jamaica Plain, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I Destroyed My Grease Filter In The Dishwasher And It Just About Disintergrated.
I just had to drop the grease filter into the slot. It took less than a second. But what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on thursday morning. It was shipped on thursday afternoon and in my driveway by friday noon!!! Wow!!! How great was that!!!!!! The fastest service I've every had for anything!! Bravo!!!!!!!! To all your workers!!!!! Rrm
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Eau Claire, WI
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
change oven sensor
Followed provided video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Polson, MT
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had code F1 and F3 on my oven. Oven wouldn't heat.
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Leighton, IA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter broke
Lifted the old one out and put the new one in. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliane from Potomac Falls, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very old grease filter.
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryAnn from Scituate, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simply replace the grease filter
Thanks for carrying this part for my old stove. And thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Newark, DE
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature was of & then taking along time to heat
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from homilton, MT
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven randomly turned off and locked
Replace the oven sensor per the excelent easy video you provided
Was this instruction helpful to you?
Thank you for voting!