FCG20600A Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from West Mifflin, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter glowed but oven would not light
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Temple, TX
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
gas burners would not light with electric ignighters
using the diagram shown on line Looked up the ignition module and ordered it by phone. Received it the next day and installed it within the hour. Previously I had called the repairman and he said it would be a couple of weeks before he could look at it and a service call was $75 plus parts..I fixed it for the cost of the module $34. I am very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FITCHBURG, MA
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
f1&f3 error> continuous beeping,oven stopped working after using the self cleaning mode
I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.
Was this instruction helpful to you?
Thank you for voting!
oven igniter although lit up it failed to permit gas valve to open
ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from covington, LA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven would not light
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Milton, MA
- Parts Used:
- 12400035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
igniter burned out
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from LIMINGTON, ME
- Parts Used:
- WP9781049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
oven light glass cover was broken
took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from haskell, NJ
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
F 3 signal on display pad every time oven warmed up
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clymer, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not turn on
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and replaced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Westcliffe, CO
- Parts Used:
- 12001655
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven did not heat up in bake mode.
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Hoover, AL
- Parts Used:
- 74003320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken glass in oven door
Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franziska from Salt Lake City, UT
- Parts Used:
- 74003320
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The oven glass shattered when I dropped water in the heated Glass
I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Albuquerque, NM
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner was sparking but not lighting
I first switched the old burner to a new position and different ignitor wiring. The problem persisted in both places, so I bought a new burner assembly and now the burner lights immediately. Very happy and a very simple replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from MOUNT HEALTHY, OH
- Parts Used:
- 12001655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had an F2 message go off then F3 when I tried to turn the stove on
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!