JDS8850ACS Jenn-Air Range - Instructions

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

Video showed element being unplugged from inside oven. My oven wires did not extend into oven cavity and they fell behind the back oven wall when I unplugged them. After trying to catch the two wires using needle nose pliers through 3/4" holes several times, I finally decided to take the complete back off the range. When I did this, I was able to see the wires with the female couplings. I then had my wife firmly hold the new element against the back of the oven from inside letting me connect the wires to the new element and replace the oven back. THIS WOULD HAVE QUALIFIED AS "EASY" AND A 15 TO 30 MINUTE JOB if this technique had been known from the outset.

Unscrewed two Phillips screws holding the element in the back of the oven, pulled out the element and the leads, disconnected the wires, removed element from oven and reversed the process to install new one. One most important and critical maneuver - the element is connected to the hot wire on the left side and the switch shuts off the element by disconnecting electrical flow to the neutral side of the power so its not enough to just have the oven turned off - makes one heck of a spark when the wire touches the stove panel when you pull the wire through the hole (220 at 60 amps).

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.

Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.