SEG196W-C Jenn-Air Range - Instructions

In oven I unscrewed orfice; replaced with new orfice. On stove top the people who make it sent a kit for $11.00, plus S & H. I installed it as per instructions.

Removed 4 screws under the top unit that holds the stove control knobs. Open oven door for better view. Tilt whole unit (width of stove) up and out of top flange. Remove knobs for timer and the two control knobs (that operate the range burners) nearest the clock. Take out the screws by these knobs, 2 per knob and then you can get the frame that holds clock unit out. Make a drawing of wires to replace on timer unit or as I un plugged one I hooked it up to the new unit. Make sure you have turned off range at your fuse box before working on stove. Works good as new now, I assume it was hit by lighting that also made me replace our garage door opener.

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I had an appliance repair rep do the replacement. He made it look relatively easy.
The repair man first turned off the breaker to the range and confirmed there was no power to the range.
After lifting off the range top cover exposing the burner igniters, he unhooked and removed the igniters. He opened the lower oven door exposing the screws which hold the front knob plate in position. He took those out. After loosening the knob plate he was able to unscrew and raise the inside cover which exposes the wires and the spark module.
My spark module was located in the front left corner area tucked a little under the knob plate. That is another reason why he had to loosen the plate. The replacement part was a universal part so he had to do a little work on the wire connectors but it only took a couple of minutes. Once he configured the wire ends, he was able to plug in the new spark module and put the top back together again.
The repair man knew exactly what to do and made it look relatively easy. I did not want to tackle this problem because I did not know exactly where the spark module was since some models have them in the back of the oven and the oven has to come out from the wall. Also, the wire connections had to be worked with a little and he knew exactly how to do that.
The repair man took about 45 minutes from beginning to end with most of that time spent getting to the part and putting it back together. The replacement itself took only about 10 minutes.

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

None of the surface burners (two Uni-burners) would light without using a match. I first ordered two replacement PS2089818 top burner spark electrodes. I replace one which was very easy - the electrode just clips into the burner - and I traced the wires down to the back bottom of the stove where I found they plugged into an ignition module. The new electrode didn't help, but since all four burners were out it made sense that the ignition module would be the problem and not the two separate electrodes. So I ordered a new ignition module. It plugged in easily with the terminals well marked like the original. I put the original electrode back in and all four burners now light properly with the desired "tic tic tic" sound with the knobs in the "high/light" position.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

Replace filter