JGR8855BDS Jenn-Air Range - Instructions

I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

Removed all screws from back panel of stove, disconnected all electrical, shut off gas. Removed valve and replaced with new. Put all back together. Turned on gas and checked for leaks. Success!!

It's happened before and the igniter has always been the problem. This time, however, the mounting holes were slightly off and had to be drilled out. The connector didn't mate up and so both had to be cut off, the wire stripped back and wire nuts used to make the connection. In the end, it all worked out. I guess since its kind of old, you can't stock every component for every oven. Oven works perfectly now.

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

Pulled the drawer and removed the oven door by pulling it upward. Then removed the two hex head screws which loosened the old hinge and pulled it down out of the side of the oven box. Replaced the new hinge in the position of the old one and installed the two hex head screws. I replaced the oven door and that was when I realized the part was wrong. The parts description in the view on the website was one number off and I replaced the broken hinge and ordered from another site the right number. That hinge works.

Firmly grasp burner turn counter clockwise while lifting. Photograph the location of the wires. Remove with a Phillips head screwdriver. The igniter will lift and turn one quarter turn then pull through bottom. Reverse the steps to install the new igniter. Test knew igniter. Put tools away

Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.

The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.

Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.

Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.

Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.

Piece of cake, really.

Total repair time: about 30 minutes, including the mandatory halfway beer break.

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice maker. Gregg in PA.

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.