JGR8730ADW Jenn-Air Range - Instructions

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

Took the old levelling leg out and screw the new one in.

unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order

Removed back panel on stove. Removed old control panel (4 screws. Unpluged wireing making sure to note color location and reinstalled control panel.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the new burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.

Put a new one in.

1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should turn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove

Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!