JGR8775QDQ Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- keith from westfield, MA
- Parts Used:
- 74007498
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven took to long to preheat
I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BEVERLY from SELIGMAN, AZ
- Parts Used:
- 74007498
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Oven would not heat
Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from McHenry, IL
- Parts Used:
- 12002604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gas leak
My Husband did the repair in less than an hour. He followed the way it was put together removed it the same way and replaced the whole unit very easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Buffalo, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from ELKO NEW MRKT, MN
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake - No Heat, Broil - Heat
There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from BARKER, NY
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electric failure ruined ignitor
same as taking out old part and i misdiagnosed the problem ordered wrong part first and parts select steered me ito the correct part thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wind Lake, WI
- Parts Used:
- WP7432P136-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My gas oven wouldn't ignite.
Diagnosed the issue by removing the bottom panel of the oven. (two little screws) Once the panel was out I turned the oven on with the door open to see what was happening.
Noticed that the heating element wasn't lighting up in order for the gas to ignite. Unplugged the oven and removed the heating element. Two screws hold the heating element in place. Removed those. Then, there is a panel on the back of the oven with one screw to remove. Once panel is removed you have easy access to the heating element connecting electric plug. Disconnect this plug by simply pulling apart.
Then, I was able to go back to the inside of the oven and slowly pull the heating element with plug out. The heating element had the part number on it. My oven is a Maytag which, is made by Whirlpool.
Went online to Whirlpool PartSelect and ordered my part. The part came in two days. Installed my new part and plugged in my oven to test the part. Part worked perfectly. Unplugged the oven and finished the installation process.
Noticed that the heating element wasn't lighting up in order for the gas to ignite. Unplugged the oven and removed the heating element. Two screws hold the heating element in place. Removed those. Then, there is a panel on the back of the oven with one screw to remove. Once panel is removed you have easy access to the heating element connecting electric plug. Disconnect this plug by simply pulling apart.
Then, I was able to go back to the inside of the oven and slowly pull the heating element with plug out. The heating element had the part number on it. My oven is a Maytag which, is made by Whirlpool.
Went online to Whirlpool PartSelect and ordered my part. The part came in two days. Installed my new part and plugged in my oven to test the part. Part worked perfectly. Unplugged the oven and finished the installation process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mohaemd from pittsburgh, PA
- Parts Used:
- 74010546
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven door would not shut all the way, so heat was leaking
The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand.
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DEPEW, NY
- Parts Used:
- WP74009147
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
poor design, knobs cracked and broke for 2nd time
repair is very easy, just needed to push them in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Horacio from La Habra, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ignitor went out
one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianna from Granite Falls, WA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven slow to light
Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Belen, NM
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven shutting off, getting an F1 error on ECM
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from DECATUR, GA
- Parts Used:
- 12001655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven did not heat, but the top burners worked fine.
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from EDGEWOOD, NM
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven would not maintain temperature and not heat up correctly
Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.
Was this instruction helpful to you?
Thank you for voting!