JER8750ACB Jenn-Air Range - Instructions

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

disconnect power to range,took top off range turn upside down, remove screws holding element, disconnect wires to element and replace element with new element put every thing back as in reverse order and the range is working fine again.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

First, I shut the power at the main box then, I removed the screws holding the element to top of stove then removed two screws in the back wall that the element was secured to. Then took pliers and pulled apart the wire and the end of the element and then just reversed the procedure and then turn on the power and it worked fine.

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.

FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

0. Throw oven circuit breaker 1. Open oven door and slide/lift door off of hinge posts 2. Remove oven drawer 3. Slide oven out from between cabinets and turn so that the back is accessible. 4. remove Phillips screws holding the cover-rear and side panel to the stove. Note which screws have pan heads and which are hex head. 5. remove stove elements and pans 6. Raise stove Top Assembly and release ceramic element sockets from their clips. 7. Push the supports for the Top Assembly fornt and back to release them from their sockets so that the Top Assembly can be lifted to near vertical. 8. Remove the hex head screw holding the Control Panel End Cap to the side panel. (Steps 5-7 might be avoided if you have a small socket wrench that can get to this screw without removing the elements.) 9. Remove the other screws holding the top of the side panel to the "Box Burner" pan that sits under the Top Assembly. 10. Pull side panel slightly away from the oven and lift it to disconnect it from the posts that hold the side panel to the front of the oven. 11. Remove the two screws on the front of the oven that hold the hing mechanism. 12. tilt and remove the hinge. 13. Open the replacement hinge so that it can fit through the hinge opening in the front of the oven. 14. Reassemble.

Repairman wanted $99 just to come look at it, then the cost to fix it. I got online, found the part, 2 screws and $40 later and all fixed. Wife baked me an apple pie that evening, better than ever!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.