SVE47100W Jenn-Air Range - Instructions

The replacement switch was not exactly as my original and none of the other instructions matched exactly with my unit. So I had to figure it out, but they matched mostly what Micheal from Colliervile wrote. Safety is paramount. Turn off circuit breaker and ensure there is no power to unit with a test light. You don't have to remove the glass top. Open oven door and remove 4 screws at bottom of control panel, then remove two screws on each end while suppoting the panel with one hand. Rest control panel on top of door or hang by wires. Remove two screws to detach switch from panel. I took pictures of the wire placement on old switch and drew a diagram of what color wire went to each terminal. I used the instruction sheet diagram of new switch and marked where each wire color goes. Here is where I put them: DOUBLE BLACK to L1,2; New jumper from P1 to S1; RED to 2: DOUBLE RED to P2; new jumper with small connector from S2 to "element on" indicator lamp (it's longer than and replaces existing jumper); YELLOW to 4a; TAN to 4. The letters in parenthesis on the instruction sheet almost matched up to my old switch so I used them to help with the placement. I didn't have to seperate any compound red wires. Double check wire placement and put it all back together in reverse order.

pulled out the old door gasket, it had little diamond-shaped clips, pulled out really easily, replaced with the new gasket. All the clips fit into the proper holes, stuffed the new ends where the old ones were. Perfect. less than 10 minutes. Thanks....

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires together and reattached sensor inside oven. A cakewalk.

First step is turn the power to the range off. Then I removed the grate covering the down draft vent in the center of the cook top. Inside the vent opening are two screws that secure a panel that holds the four knobs that control temperature settings. Remove these screws. Slide the panel tward the back of the range while lifting it up. This will allow removal of the panel. Remove the knob from the burner control you are replacing. Under the knob are two screws. Remove the screws and let the controller drop out of the cover panel. Take the new switch and carefully remove the wires from the old controller and place them on the new controller in the same position. When the wires have been connected, put the controller back in the control panes and secure it with the two screws. Replace the panel back into the cook top. Tilt the control panel so the front is low and the back is elevted. Engage the lugs protuding out on each side of the control panel opening. Lower the panel back into the opening and secure it with the two remaining screws. Replace the control knob and you are done. You just saved yourself a $125.00 service call. Total cost for the controller $35.00.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Removed the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Removed the door saftey plates lifted the door out of the hinge pockets, took the door to my work bench, removed six phillips screws which keeps the door glass cover in place, removed two screws form each hinge removed the old hinges put new ones back in place and reversed the disassembly procedure all in all about twenty five minutes.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new element. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

Diagnosis is the important aspect. Ovens have plunger-type switches to tell the "brain" door is closed, both for the light AND to allow initiation of self cleaning. Finally discovered one of those switches was "scratchy" in operation and unreliable in closing the circuit. (Push the plungers in and out several times and observe the light.) If not 100% reliable, replace that switch (cheap and easy with a Phillips screwdriver.) Initial guess was a $major "brain"-electronics problem but it was merely a sticky switch. Strange since the unit is about a year and a half old and rarely used. Found the part easily with PartSelect, and it came via UPS quickly.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!