Models > SEG196W > Instructions

SEG196W Jenn-Air Range - Instructions

Jump to:

All Instructions for the SEG196W
91 - 105 of 173
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Charles from Bangor, MI
Parts Used:
74005189, WP7505P283-60
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Old burners were worn out and wouldn't light with the ignitor
Removed two screws and replaced burners and placed the unit back into position and the burners worked perfectly. Very easy. I think anyone could do this task.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
alphonso from plainfield, IL
Parts Used:
WP71003558
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ernest from Hohenwald, TN
Parts Used:
12200039
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
The fan/light switch was defective
Turn power off to stove. Removed two screws and lift out switch assembly. Removed each connection one at a time and placed them on the new switch. i tried the compression fittings that were sent but they were to small as I had read elsewhere so I used two small nuts to reinstall the switch. I took less than 30 minutes.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Larry from Portland, OR
Parts Used:
12200039
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers
Fan and oven light would operate.
Removed the old part by removing the clips and wire connectors. Then placed the new switch in place and reapplied the wire connectors. Tried to then place the new clips on the posts but the clips were very fragile and they broke. Then decided to thread the posts and use nuts. Used a minature die to thread the posts, applied washers and nuts and finished the job.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Henry from Smithfield, VA
Parts Used:
WPY04100514
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The broiler would not heat. I saw a bad place in the element. Ordered a new one.
Received the new one. Installed it in 15 minutes. Thanks for the fast service.I will buy from you guys the next time I need a part ! Thank You, Henry
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Wilson, NC
Parts Used:
WP71002111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
not a prblem,just necessary to replace
even though these sre washable filters it's still necessary to change them after so much time
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from Palm Coast, FL
Parts Used:
WP8203546
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
3 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from Fair Oaks Ranch, TX
Parts Used:
12001311
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
Blower motor had frozen up.
Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Frankfort, KY
Parts Used:
W11117769
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sarah from Albany, GA
Parts Used:
WPY702338
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
worn door seal on oven
takes two people to put the oven door back in place but otherwise very simple as long as you keep all your screws and pads in place
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ivanka from Atlantra, GA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from East Greenwich, RI
Parts Used:
WP71002111
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced the current warn-out grease filter
removed the old by pulling it out of track and replaced it with the new filter
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from Wellesley, MA
Parts Used:
12200039
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Old switch was difficult to remove and the push nuts provided with the new switch were too small to fit on the lid posts.
Removed the old switch by essentially destroying it with a screw drive and pliers. Had to drive to the hardware store to purchase push nuts that fit.
.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Pleasant Hill, MO
Parts Used:
12200039
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Downdraft fan would not operate with light/fan switch.
Removed old switch, but when I tried to install the new one the round slide on retainers that hold the switch in place were cheaply made and broke. I had to go to the hardware store to find replacement parts. Electric terminals matched correctly and slipped off and on just fine. New switch works great.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the SEG196W
91 - 105 of 173