S136W Jenn-Air Range - Instructions

Purchased 2 piece broiler pan from this site

We made the mistake of taking the door apart before we received the replacement parts. After waiting several days, which was fine, the parts arrived. Then we had to figure out how it went back together. My wife and I did it and enjoyed working on it. However....after getting it partly reassembled, we (I) found four extra screws. We took it apart again and then put it back together. Turning the door over we found that the glass assembly had slipped. This meant that we had to take it apart again. This went on two more times LOL. Then the gasket gave us a couple of small fits as well. All in all it was a neat experience. I do suggest, unless you are experienced in appliance repair, to NOT disassemble the door until the parts arrive.

The comments from others on the website were a great help.

Thank you.

I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

I changed out the infinite switch without any problems. The indicator light was another problem. It wasn't the light that was bad, it was the indicator light lens that snaps into the panel. The light then attaches to the lense. The lense broke and the indicator light pulled away with the tension on the wires. Now I have to order replacement lens and will have a spare indicator light.

Removed 4 screws under the top unit that holds the stove control knobs. Open oven door for better view. Tilt whole unit (width of stove) up and out of top flange. Remove knobs for timer and the two control knobs (that operate the range burners) nearest the clock. Take out the screws by these knobs, 2 per knob and then you can get the frame that holds clock unit out. Make a drawing of wires to replace on timer unit or as I un plugged one I hooked it up to the new unit. Make sure you have turned off range at your fuse box before working on stove. Works good as new now, I assume it was hit by lighting that also made me replace our garage door opener.

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

Simple, take off the old and put on the new/ Delivery was excellent (next day).

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

Serviceman took out broken glass by removing door and separating front of door from back of door. He carefully removed all broken glass Then replaced with new glass and fastened door together . He did repair in 20 minutes. Oven is like new. Thank you very much for still stocking this part that allows me to keep my oven repaired.

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.