JDS9860AAB Jenn-Air Range - Instructions

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

First, I shut the power at the main box then, I removed the screws holding the element to top of stove then removed two screws in the back wall that the element was secured to. Then took pliers and pulled apart the wire and the end of the element and then just reversed the procedure and then turn on the power and it worked fine.

Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.

I haven't done anything yet because the part I am replacing is different from the one i have to order. I guess you might say I am getting screwed. I purchased the grill burner for $234.00 plus tax and shipping. Then realized I needed to purchase an igniter. My original one came with 2 igniters attached to the burner part. These new ones are all separate. $55 and $49 if i remember correctly. I ordered just the larger one and I am hoping I do not have to buy the smaller one. The large igniter will not even arrive until the end of August that is 6 weeks after the order date. I was told by the customer service rep it would only take 10 days to get it to the warehouse.The price tag is over $500 just to replace the grill burner on my stove top.That is some rip off. Otherwise my stove top is in excellent condition.

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

Repairman wanted $99 just to come look at it, then the cost to fix it. I got online, found the part, 2 screws and $40 later and all fixed. Wife baked me an apple pie that evening, better than ever!

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall
(would only come out about a foot and a half due to the gas line connection). Removed the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.

First I removed the two screws on the bottom heating element that hold the element in palace,one on the left side one on the right side, I then pulled the element out about 2 to 3 inches and disconnected the two wires. I then installed the new element. It took me about 20 mins. The cost of having some come out to fix this was about ten times of what I paid for this part. Thanks for the quick service.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

turn off breaker take two screws loose from back of oven slowly pull out element unplug element an plug new element in push element in place an put screws back in turn on breaker done

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.