SCE4340B-C Jenn-Air Range - Instructions

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.

First I removed 7 screws, using a Philips head screwdriver, to allow access to the inside of the oven door. I then removed several more screws to separate the panel holding the seal so that I could remove it and replace it with the new seal. Once the seal was in place I re-inserted all the screws to the panel and door to complete the repair. The knobs just slipped on to replace the ones that broke and fell off.

Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.

Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!

1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.

Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connector from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.

I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything worked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.

It was easy to get apart. I drew out a schematic of where the wires were so I could put them back in the same place. I plugged them all back up and it worked! Only problem was, there was a dead mouse behind the panel! He had not chewed anything, so the unit just went out from age.

I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.

Removed top and front panel

Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.

Screwed in light bulb and glass protector

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy