JER8550AAW Jenn-Air Range - Instructions

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

We moved into a house with seemingly newer looking appliances. After the dishwasher broke and destroyed our floor, we found out that they were all twelve years old. Amazing the condition they were in after all that time.

The oven was the next thing to break. The hinge snapped, and while we could still use the oven, it allowed hot air to seep out.

So I checked online and lo and behold, I found a hinge for under $20. Wow. Much cheaper than a new range.

The most amazing thing was that I purchased it on a Friday afternoon, and it showed up on Saturday, so we could do the repair over the weekend. I cannot tell you how impressed I am with that kind of service.

We had to take off the side panel which was a pain, but all in all, it was 7-8 screws and swapping the hinge was easy. One of the screws did not want to go back in, so I had to find a replacement, but other than that, it was a pretty easy repair.

Thanks!

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

After watching the instructional video (and flipping the breaker to my range) it was straight forward and simple. The heating element was a little bent so didn’t originally sit square/flat to the bottom of the oven so I uninstalled, bent it gently a little and reinstalled and it set down flat. It still didn’t take 15 minutes.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Watch the video. Spot on instructions. Easy peasy.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

oven had to completely come out cause two sheet metal side panels had to be removed to get to hinge.

Plugs in easily, screws to secure

Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.

Turned oven circuit breaker off. Removed oven racks. Removed 2 screws from old element. Pulled element out slightly disconnected wires on each end and reattached to new element. Pushed back in and reinstalled the 2 screws, reinstalled oven racks and turned circuit breaker back on. All done in about 20 minutes.