Models > FCE2012W > Instructions

FCE2012W Jenn-Air Range - Instructions

Jump to:

All Instructions for the FCE2012W

Customer:: burton from prides crossing, MA
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

hot spot in center of bake element appeared suggesting failure was imminent

pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Matt from Lewisburg, TN
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

BurntBaking Element Element

Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PRESTO DONE

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Herbert from Neenah, WI
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

The oven heating element burned out like a lit fuse!

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Paola from High Bridge, NJ
Parts Used:: WP12001560
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Just plugged the burner in and it was good to go.

The burner wouldn't work. I just plugged in the new one and all was done.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: James from Allyn, WA
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Element burned in half

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from Funston, GA
Parts Used:: 12001656
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

oven not heating to set temp. 100 degrees too cold

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Paul from Yukon, OK
Parts Used:: WP74003019
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

snapped element

switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: John from Fishers, IN
Parts Used:: WP74003019
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Lower burner not heating:

Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.

John
Johnny on the Spot Home Repairs
Fishers, Indiana 317-997-3600

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Donald from Tomahawk, WI
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins

Bake element burned out

Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.

Don Samuelson

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Edward from Adamstown, MD
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

No Bake, only Broil

POWER OFF! Unplugged oven from wall.

(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)

Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: robert from merrimack, NH
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

oven didn't heat up

removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Susan from Grand Ledge, MI
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

bake element disintegrated!

Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: PATSY from HALLWOOD, VA
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Lower element out-oven wouldn't heat

I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jonathan from Havertown, PA
Parts Used:: WP74003019
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Oven wouldn't heat

Easiest repair ever.

#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws

Everything took 15 mintes max.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from Jacksonville, FL
Parts Used:: WP74003019
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Bottom Element Burned out

Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)

Reversed the process.

1 person found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the FCE2012W