20135 Jenn-Air Range - Instructions

Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.

First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.

Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.

First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

Important: 1) ALWAYS REMOVE ALL POWER FROM THE STOVE. 2) Do not "preassemble" the ceramic recepticle and wire kit. The wires are nearly impossible to remove from the receptacle once inserted. The wire colors have changed and are not the same color as your old wiring. 3) All the fasteners are sheet metal screws, different sizes (note where they are used) and are easly stripped if tighted too hard. Either unplug the stove or open the main circuit breaker to the stove. Take out the right-hand burner cartridge and place it aside. remove the center screw and metal strip from the old receptacle (you will reuse this item). Loosen the control panel from the front of the stove by opening the oven door and remove the four screws holding the control panel in place (Screws are located on the underside of the control panel). The panel slides down about 1/4 inch and tilts forward exposing all the control wiring. Ues a hex-headed driver or large screw driver and remove the drain plug from the drain pan. Use care as there is a small gasket under the drain plug. Remove the four screws holding the burner's pan to the stainless steel stove top. Move the wire bundles aside and GENTLY pull the burner pan half-way out of the stove (it is a tight fit but do not use force. Remove the screws and strap holding the old receptacle from the pan. Withdraw the pan from the stove. (good time to clean the pan and drain plug) With the old receptacle now exposed, assemple the new receptacle and wire harness wire for wire carfully replacing each lead. The new wire harness is inserted into the new receptacle thru the top of the receptacle and will lock in place within the new receptacle. The blades on the end of the wires must point toward the slots in the receptacle. The receptacle wires will be pointing down. Trace each wire and be certain the correct wire is switched out with the proper lug on the control knobs within the stove (needle nose plyers will help but do not force the connections). Gently push the pan halfway back into the stove and attach the new receptacle to the pan with the small metal strap across the back of the receptacle with screws. Push the pan all the way back into the stove and re-attach the pan to the underside of the stove top with sheet metal screws. Re-install the drain plug and drain tube. Tilt the control panel, slide the panel back up into the front of the stove and reattach the control panel with sheet metal screws. Re-install the small metal clip into the front of the receptacle (one end of the clip slides under the stove's stainless top frame). Reenergize. Reset the clock. You're done.

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

Just replaced old with new, it plugs in same as old.

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!

Easy job. Anybody can do it. This replacement is accessed from inside the oven.

1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.

Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.

Unscrew the two screws. Pull the element out a few inches. Unclip the wires by pulling them apart. When we did this the wires retracted back into the opening. It was difficult to reach them and pull them back out. Be sure to hold the wires or clip something on them to hold them out till you can attach the new element. Attach the new element wires and screw the plate back on.

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.