FCE30610WC Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from AIKEN, SC
- Parts Used:
- W10823704
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element burn out. Would not heat
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Seth from Old Orchard Beach, ME
- Parts Used:
- W10823704
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced Burned-out Cooktop Element
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included extension wire for one that would not reach with the new configuration and everything works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeri from NEW RICHMOND, OH
- Parts Used:
- 74002312
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the broiler drawer guides broke
All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Rolla, MO
- Parts Used:
- W11690131
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lens light was broken and missing.
Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop
and turned electrical power on.
and turned electrical power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from PATERSON, NJ
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Element didn't heat at all
Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Tomahawk, WI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bake element burned out
Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.
Don Samuelson
Don Samuelson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Jacksonville, FL
- Parts Used:
- WP74003019
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Element Burned out
Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)
Reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATSY from HALLWOOD, VA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element out-oven wouldn't heat
I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Havertown, PA
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven wouldn't heat
Easiest repair ever.
#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws
Everything took 15 mintes max.
#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws
Everything took 15 mintes max.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Medford, MA
- Parts Used:
- WP74002066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle broke off of the trim
1st I looked for the mounting screws and determined the tolls needed. I then removed the the screws required and took off the old trim. I then cleaned the area around the trim piece and installed the new trim. i reattached the handle and the job was done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Adamstown, MD
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No Bake, only Broil
POWER OFF! Unplugged oven from wall.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from merrimack, NH
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven didn't heat up
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Grand Ledge, MI
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bake element disintegrated!
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from ROCHESTER, IN
- Parts Used:
- WP74003019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element had burnt in half.
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from BOULDER, CO
- Parts Used:
- WP74003019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element burned out
Removed the failed bake element per the video linked in the Partselect email. Unlike the video on YouTube the PartSelect video shows that the bake element can easily be replaced through the oven door and it is not necessary to slide the range out and remove a rear panel.
Was this instruction helpful to you?
Thank you for voting!