JDS8850BDB Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kath from Horseheads, NY
- Parts Used:
- WP74011664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn burner knob
Exchanged knobs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Hamburg, PA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced gasket around inside door
It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Tampa, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not turn on
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Newport News, VA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket
Removed old gasket and replaced with new gasket'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from roseville, MN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Eau Claire, WI
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
change oven sensor
Followed provided video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Polson, MT
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had code F1 and F3 on my oven. Oven wouldn't heat.
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Dacula, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan runs continually ,door locked,error code f2,f3,f7
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monee, IL
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!