FCG20510A Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Merrimac, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Oven burner would periodically go out and re-light
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Cotton, MN
- Parts Used:
- 74003320
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The inside glass was broken on oven door.
I was pleased with how the job went.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times.
There were more screws than mentioned here.
Someone said 10 screws but there were 12.
In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaime from Brooklyn, NY
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Burner head were clogged with grease
First I removed the old burner head by twisting it counter clockwise by using wide channel lock pliers. When It completely came off, the burner head had deteriorated so much that it almost came apart. When I took off the 2 wires from the burner head it also easily came apart. The burner-head was in really bad condition. I cleaned the whole area and connected the 2 wires to the new burner head and hand tightened in a clokwise direcrtion. It took 20 minutes to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Appleton, ME
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heads were rusted out, releasing flames from underneath and also clogged with carbon dust
Very simple! Unscrewed the burner heads with a simple twist, unplugged the two wires from the old head, plugged them into the new one, then screwed that back in. The flames are MUCH better - more efficient and safe. thank you! ( Only issue was when we ordered we didn't see a choice of color and the new ones are different, but it really doesn't matter on an older stove anyway.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Fremont, CA
- Parts Used:
- 74002312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler front drawer slides broke
I noticed the drawer on the broiler was sliding crooked and found the plastic slides had broken. Of course I thought it would be a hassle and not worth the time to fix it. I would just "live with it". Boy was I wrong, it was probably the simplest fix ever. It was easy to get the correct parts from PartSelect with their exploded and concise diagram. The parts were ordered and delivered in a couple of days. It took me all of 10 minutes with a screwdriver to make the repairs. Now it is a good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Chapell Hill, NC
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven heat loss, door gasket needed replacement
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Atlanta, GA
- Parts Used:
- 74002312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler drawer didn't track poperly
Remove screw securing the broken drawer guide. Placed new drawer support in place and tightened screw. Replaced drawer. All done in less than 5 minutes (and cheaply).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from tisbury, MA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap had rusted out
It was pretty much a plug it in job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Monroe, NY
- Parts Used:
- WP5504M003-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
floor panel heavily stained and warped
slide latches in rear of floor panel forward and remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Duarte, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Was Not Getting Hot
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PEORIA, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven igniter came on but the gas valve never turned on.
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from SHOREVIEW, MN
- Parts Used:
- WP9781049
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from West Mifflin, PA
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter glowed but oven would not light
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FREELAND, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The problem was exactly what was described on your site.
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. After removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Was this instruction helpful to you?
Thank you for voting!