D140 Jenn-Air Range - Instructions

I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.

Being a single Mom for almost 16 years I have learned to do everything. When the Jenn-Air oven baking element started on fire I freaked out. It turns out that PartSelect.com has the part as usual. I have ordered before for the same appliance and even though it is 15 years old you always have what I need. I removed the old one (two screws in back of oven), measured, logged on, ordered, and the next day installed the new baking element. Even I was able to do this and it fit and worked the first time!!!!

Turned off the power at the circuit breaker panel. Removed the control knobs from each switch and the four palnuts under each knob. Removed the two screws inside the vent well that hold the escutcheon in place. Pulled each switch up as much as possible to expose the wires attached underneath to each switch blade. Remoced each wire and replaced them on the new switch. Same procedure for all four switches. Reassembled in reverse order. Turned on power and all four burners lit up and were regulated as if new. I saved $244.00 doing the repair myself.

The element plugged in to the cook- top.The cook -top was working moments after i unpacked the element. thank you.

Jim B.

My spouse calls me Mr. Breakit--and she's right. I was delighted to read others' accounts that this was easy, but I wasn't sure. When the part arrived, we had 1 hour before company arrived. I took two screws out of the plate (tight--I had to apply a lot of torque), slid the old piece out, attached the new piece, put the screws back in. Voila! (Oh, yeh, do remember to turn the juice off.) We were "cooking" in about ten minutes. So easy a caveman could do it. And I did.

"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again.
So easy even I can do it. !!!

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

The oven that was in out newly purchased house was a JennAir and over 20yrs old. Worked ok, but as with any heating element, the performance wanes over time. I decided to replace the baking and broiling element...and the oven door seal while I was at it. Everything went well, it was a simply remove/replace. Then I bumped the oven door where it was leaning up against the fridge waiting to be reinstalled. Down it fell on the tile floor. SMASH! Tempered glass EVERYWHERE. Got online with PartSelect and ordered a replacement (very reasonable price). It arrived in 2 days...just like the elements. Replacement was easy. Thanks to PartSelect for having the parts in stock and delivering them in record time!

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

As described elsewhere. If the two retaining screws are rusty, order new ones with the element. They are expensive, so take them out and check before placing the element order. Save time and shipping costs.