S110 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Horace from Las Vegas, NV
- Parts Used:
- WPY702338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replaced worn seal
Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Camilla O from Sanford, NC
- Parts Used:
- WPY702338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range seal worn and leaking
removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Llewellyn P. from Junction, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Jennaire 4 burner stove top right two burners coming on full heat with either controls.
Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from springfield, PA
- Parts Used:
- WPY04100514
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Failed Broiler element
Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gina from Oak Harbor, WA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
A burner on the cook top stopped working
I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- I R from Montgomery, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Faulty infinite switch
Turn off the power!!! Remove two screws from back of switch section and pull toward you. That was the tricky part; it wasn't obvious to me how to remove the section. Then simply revmove the witres from the old switch one by one and put them on the new part. Close it up and you're good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from Waterville, OH
- Parts Used:
- WPY702338, WP7711P466-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Missing nobs...I installed them!! Ha...It took time to take the oven door appart for the seal.but no problem. Door latch required the drop in oven to be pulled out. Need some he men for that. If done within 90 days...no extra charge.
Called Sears as they will install parts you have purchased. I am a 67 yr. old woman. Already had the new element. Cut my cost by almost 2/3rds as other companies charged a fortune to guarantee their own work with their own parts..Which they probably get from you!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from MCLOUTH, KS
- Parts Used:
- WPY702338
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Biggest problem was trying to get the two hinges to open up so that the door could be reinstalled to the hinges.
The basic replacement of the bad seal went fairly well. Just had to follow the other guidance and pay close attention to the correct sequence so that the door goes back together as it should be. The only real difficult part was when attempting to hold the hinge downward so that the door could be properly placed back on the hinges. After closer examination I discovered that there were two holes in each of the hinges that when they were opened all the way that the holes lined up and I cut off two nails approx 2 inches long and then once I was able to pry the two hinges all the way opened and then I used them to slip in through the two holes and they worked just fine and they held the door open, until the door could be re-installed. Once installed the nail/pins could be easily removed with some needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!