SVD48600PT Jenn-Air Range - Instructions

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

My husband did the repair. He had difficulty removing the old element, probably because it had been in there for 20 years. Once he got the old element out, it took less than 30 minutes to install the new one.

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.

lift out old filter, wash, put in new filter.

I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.

Called Parts select and they replaced it in two days.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

I cut off the electricity. Removed the back panel. Moved 1 wire at a time from old board to new board. Then removed the old board and replaced the new one. Reattached the back panel and turned on the electricity. I was happy when the oven began to heat.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!

After getting help from customer support, I was able to order the part. I tracked the part on FED EXp.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.

Removed the old coil and plugged in the new. 2 screws held the coil into oven connector.

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.