SCE70600B Jenn-Air Range - Instructions

My husband did the repair. He had difficulty removing the old element, probably because it had been in there for 20 years. Once he got the old element out, it took less than 30 minutes to install the new one.

1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

I removed the 4 screws that hold the control assembly to the range and observed that the clock assembly/control board appeared easy to remove.

Ordered the replacement board and it came a day sooner than the shipping I paid for. Only took about 10 minutes to take the control assembly off again and install the new.

There were no instructions with the part....the ribbon connection to the board was a little tricky to figure out...when I first released the clamps that held the ribbon to the board and pulled the ribbon out, I thought I damaged it....never seen a connection like this.

The range works fine now but it should be noted that this part is the logic control board for the entire range. The board malfunctioned over a period of time. First time, the entire oven shut down in the about half way through the preparation of Thanksgiving meal a few years ago. I couldn't bring it back to life and luckily, we had another oven to finish the turkey.

Next, we had trouble with the electronic pilots on the burners. You would turn the knob for one burner and it would attempt to light another burner.

Then the oven would not shut off when the Cancel/Off button was pressed. Would have to go and trip the main breaker to turn off the oven!

This replacement part cost $126 which is a bargain considering a new oven would cost over $2000. And it works great now. But I don't trust this appliance and I get this feeling that I threw good money after bad.

However, my experience with PartSelect was great and I will use them again. I just hope I don't have to spend more money on this applicance.

Open the door and remove the top screws holding the hinge retainer plates. Remove the three screws holding the glass in place at the bottom, the three screws and two nuts holding the top cover. Remove the glass, then the two screws holding the hinge in place. Reverse order for reassembly. Easy fix, but don't do what I did. I went cheap and only replaced the side that was bad only to have the other side go bad a few weeks later. Change both at the same time.

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

I cut off the electricity. Removed the back panel. Moved 1 wire at a time from old board to new board. Then removed the old board and replaced the new one. Reattached the back panel and turned on the electricity. I was happy when the oven began to heat.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Turn off the electrical breaker before starting! Open the oven door & remove the 4 silver hex head screws under the bottom of the control panel with a 1/4 " nut driver. Pull out on the bottom of panel. This will access the clock assembly. Unplug the ribbon cable by pushing in & up on the small clips on each end of the connector - this is a little tricky but not that difficult. Remove the two small connectors and remove the two clock assembly mounting screws. Reverse the procedure for installation. This corrected the problem with the broil element not working - apparently the electronic clock assembly was the problem there as well.

I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.

I took the broiler pan out of the shipping container and put it in the oven.

it took me longer to get my portable screwdriver from my shop than to remove four screws from the panel and two screws from the clock assembly and to unplug and replug wiring , then reassemble the panel

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

There were only 4 screws to remove to take off the thingy that houses the electronics portion. Then, there was a ribbon connector and two push on connectors to unconnect. Unscrewed the 4 nuts holding the faulty Assembly in place, replaced with new Assembly, and reversed the process.

That easy. The only problem was making sure which of the parts we actually needed.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.