JGS8750BDS Jenn-Air Range - Instructions

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Put a new one in.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.

replaced heat sensor

This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.

Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!

With no rust, this should be an easy 5 minute replacement. The burner now works great!!!

Installation is simple and very straight forward. Problem, was i stripped the torx screw to release electrode because the screw was frozen. I then tore electrode out leaving space to use penetrating oil (inaffective ) then using a chisel to pop the screw out. It came out intact and did not damage the threads in the burner. So what could have been a 20 minutes job, turned into over an hour. But still worth doing myself.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

The porcelain cracked on the burner igniter, it wouldn’t spark and light the flame. I got tired of using the fireplace lighter to light this main burner.

If you have to replace your igniter, it should be very very easy. Remove the two torx screws Holding the cast iron burner to the stainless steel top. Pull it up and the wire connected to the igniter should pull through the small hole in the stainless steel top. Turn the cast-iron base over, pull the wire off, and there is a little screw Fastening the igniter to the bottom of the cast-iron Base. Remove the old igniter and screw the new igniter in place, reattach the wire, and screw the base down to the stainless steel top. That’s it, or how it should be. After years of spaghetti water, gravy, etc. boiling over, I was only able to remove one of the torx screws after using some WD-40 and a torch to heat it up. The other screw sheared off at the head. And a little screw holding the igniter in place, the Phillips head was stripped! I had to leave the roof or the igniter in place, break off all the porcelain, and then break the rest of the metal off leading the screw in place. So I had to use my Dremel grinder to remove some of the metal on the new igniter, then use some tinfoil underneath it to stabilize it in place and then tighten the cast-iron base down using only one screw. Even with one screw and using the tinfoil, it is stable and everything works now. This $27 part was a heck of a lot cheaper than paying $5000 for a new range top!

Watch the video. Spot on instructions. Easy peasy.