S136B Jenn-Air Range - Instructions

- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

First I removed the four torx screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I installed the new element in reverse order. Recycled the cardboard box and the old element.

Removed the 4 screws on the bottom of the panel, lifted the panel out and up to clear the uper part of the panel. Removed the screws from the left and right switches, which hold the bracket of the clock, marked the wires of the clock and removed the wires. Installed the new clock in reverse. The power to the range was off.

Replace filter

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.

The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

I first bought an oven thermometer to check temperatures at different levels. Temperature was about 10 or more degree off. I next looked at the manual and found you can make an adjustment to the temperature knob. This didn't make a difference. Decided I would replace the bottom heating element. I ordered and got the element in a matter of days.
The hardest part was loosening up the screws on the bracket for the old element. Thus the use of the vice grip came in handy. My oven is 20 years old!!! I'm sure I saved my husband a couple hundred bucks worth the repair guy.

My thanks to "Part Select" for making the process so easy to order and get a replacement. The repair guy finally called yesterday. Five days after I repaired the oven myself.

Go Girls, you can do it!!!!!!

After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.