SU130 Jenn-Air Range - Instructions

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Had to remove the glass top and the control panel and the panel bracket then use angled needle nosed pliers to compress the retainers then pull the switch from the inside of the oven

Removing the oven door and several layers of metal to get to the seal, is a fairly easy process. Our door had three different fasteners, torx head screws to remove the door, a very small flat head screwdriver to remove the chrome door trim screws, and a nut driver to remove the inner panels and glass. The replacement seal is over-large and must be trimmed. Care should be taken when fitting the integrated wire. Bending at the corners only, makes assembly much easier. Reassembly is the reverse of diassembly. Care must be taken that the seal wire hasn't popped out of it's seat when the cover is installed. This is the most time-consuming and frustrating part of the repair. Patience is paramount to get a good fit. Because I had made an odd bend in it, about one inch of wire was not properly seated after the cover was seated and tightened down. I was able to gently squeeze it into the seat with a flat tip screwdriver without removing any screws. The final problem area is reinstalling the door. Although two people would be helpful to accomplish this Task, I was able to accomplish it with the aid of a three foot piece of 2x4. By wedging the piece of lumber behind both hinges, they were held open under tension to allow slipping the door on. Once partially installed, the 2x4 can be removed and the door seated. Hope this helps.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

I removed the back of the stove for easy access to the wiring (three hex head screws) and removed the two wire leads. Then I began to remove the mounting screws from the inside of the oven, the first three screws came out fine the last one was so tight that I had to resort to vise grip pliers. Jenn-Air should have used hex head screws instead of phillips head inside the oven. Finally after about 15 minutes the last screw came out. I installed the new element, reinstalled the screws and wires. Then I replaced the back and tested. Total about 45 minutes.

Removed the door removed 2 inner panels Installed and reassembled A Cake Walk NOTE be careful not to strip threads

Replaced the control.

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.

My husband and I couldn't believe we were able to do this!!!So easy! We were dancing around the kitchen!!!!! We credit the advice of other do-it-yourselfers. Very accurate and true. It took less than 10 minutes after the screws were WD40'd. In addition, we recommend: use a flashlight to see in the oven since it's dark with the power cut off , and use this time to clean behind the stove!!!!!

ordered new broiler pan

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

I simply popped the knob on the switch. Easiest thing in the world!

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.