SVD48600PK Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- richard from SAINT MARYS, KS
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BOLIVAR, TN
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Front burner wouldn't light because hole burned in metal tube that channelled gas to burner
So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Carlisle, PA
- Parts Used:
- WP71001680
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Oven wouldn't heat and hold temperature.
I removed the screws that held the element in place. I then pulled the element out and disconnect the two wires. Connected the wires and place element in place and screws to hold in place.
Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.
Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Belchertown, MA
- Parts Used:
- 71001129
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven door slammed shut and the door lock switch broke causing the light to stay on continuously.
I contacted a local appliance repair store who didn't know what I was talking about. I looked online and the store called me back to tell me the part would probably be $75.00. I took the broken part out of the door frame and found the exact part online at your site, and ordered it for $14.00. Received the part within 2 days and put it in in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burma from Section, AL
- Parts Used:
- 3401X055-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The painted finish on the pan for my range started flaking.
Called Parts select and they replaced it in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portland, OR
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner inoperative
Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Clinton, IA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temperature was 50 degrees low
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grady E from Vidalia, GA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed Replacement Filters
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Palm Coast, FL
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
didn't ignite gas range.
After getting help from customer support, I was able to order the part. I tracked the part on FED EXp.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H from Newfoundland, PA
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Ports were worn and oversize
Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Houston, TX
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No temperature control
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ila from Carthage, NC
- Parts Used:
- W10757086
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven would not heat
I cut off the electricity. Removed the back panel. Moved 1 wire at a time from old board to new board. Then removed the old board and replaced the new one. Reattached the back panel and turned on the electricity. I was happy when the oven began to heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from SOLON, IA
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature fluctuates
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from PAYSON, AZ
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
"F3" error message and no oven heat
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Was this instruction helpful to you?
Thank you for voting!