SCE4320W Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kathy from indianapolis, IN
- Parts Used:
- WP5700M600-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
thermal glass within oven door window shattered
The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from MCLOUTH, KS
- Parts Used:
- WPY702338
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Biggest problem was trying to get the two hinges to open up so that the door could be reinstalled to the hinges.
The basic replacement of the bad seal went fairly well. Just had to follow the other guidance and pay close attention to the correct sequence so that the door goes back together as it should be. The only real difficult part was when attempting to hold the hinge downward so that the door could be properly placed back on the hinges. After closer examination I discovered that there were two holes in each of the hinges that when they were opened all the way that the holes lined up and I cut off two nails approx 2 inches long and then once I was able to pry the two hinges all the way opened and then I used them to slip in through the two holes and they worked just fine and they held the door open, until the door could be re-installed. Once installed the nail/pins could be easily removed with some needle nose pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marylou from NORTH BENNINGTON, VT
- Parts Used:
- Y704660
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem just wanted new oven racks
take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Rougemont, NC
- Parts Used:
- WPY04100021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out
undid the 2 screws inside the oven holding the element in place. slowly pulled the element out to get to the wire on the end. unplugged the old element and pluged the new element in and slowly slid wires and element into back of oven. secured with the 2 screws and turned on to check operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from McKinney, TX
- Parts Used:
- WP7711P492-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic knob
Placed new knob directly on post. No problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Bothell, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear butner no longer worked after liquid was spilled on range.
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Attleboro, MA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.
Thank you for your help!!
Bob
Thank you for your help!!
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Woody from New Castle, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner always on high, no temp. adjustment.
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from snellville, GA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner stays hot
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharyl K from Nampa, ID
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left Rear Burner would not work
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clive, IA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dropped cast iron pot broke switch shaft off
The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Woodland Park, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Camilla O from Sanford, NC
- Parts Used:
- WPY702338
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range seal worn and leaking
removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.
Was this instruction helpful to you?
Thank you for voting!