2810ERS Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ronald from ESTERO, FL
- Parts Used:
- WP5700M611-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
drain jar lids rusted and broken of their mounts
The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wade from CARMINE, TX
- Parts Used:
- 707704K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Motor bearing failure after 34 years.
Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.
My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.
Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.
Wife is happy...
Wade
My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.
Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.
Wife is happy...
Wade
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois G from Baltimore, MD
- Parts Used:
- 708706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Degrees were illegible.
I removed the old knob and replaced it with the new Maytag knob which worked.
I was especially pleased because another website had listed the part as unavailable, and a local parts store said they could not help me. Our range is at least 30 years old.
I was especially pleased because another website had listed the part as unavailable, and a local parts store said they could not help me. Our range is at least 30 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shaker Hts, OH
- Parts Used:
- A405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken vent cap
Unscrewed old cap, installed new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Niceville, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
smell of a dead animal
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Baton Rouge, LA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old filter to replace
:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
worn out control knobs that couldn't be read.
Simply pull off old knobs and replace with the new parts. Didn't think I was going to find replacement parts. The equipment is actually over 25 yrs old. Thanks for partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Russellville, KY
- Parts Used:
- 708706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
nubers worn on thermostat knob
Ordered new one, it came, and I put it on. The hard part was finding the model number,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from NEENAH, WI
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Numbers on surface burner knobs were illegibel.
I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from montgomery, NY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling legs
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve
Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Garland, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were worn badly
Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.
It was very easy, and the part was the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Weatherford, OK
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my old knobs were so worn that I couldn't see the numbers
I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from MOLALLA, OR
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All four knobs were stripped
We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- beatrice from TUCSON, AZ
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were wearing out, metal rims were falling off.
Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.
Was this instruction helpful to you?
Thank you for voting!