SVE47100B Jenn-Air Range - Instructions

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Simple, take off the old and put on the new/ Delivery was excellent (next day).

Sunday, four days before Thanksgiving, our oven would not bake properly. A quick check indicated the top element was not working. What to do? Where to get a part in time to fix for Thanksgiving dinner? The answer was easy - PartSelect. I had the part in my hands on Tuesday AM. Oven was fixed in 15 minutes and my wife was baking pies within an hour. All worked well and yes, we had a wonderful trukey dinner. Great service !

Removed old part with a pair of pliers and plugged the new part into place.

Very simple and the self cleaning feature works again.

Blower motor stopped working and the breaker tripped. Horrible smell! from the somewhere in the oven. Looking at the wiring diagram told me that there was a relay board feeding he motor, but I had no idea where it was, which took a little Internet searching to find it. Finally seeing that it was in the rear I was happy to see that there was enough flexible gas line to pull out the stove enough to check the board, which was fried. I replaced the board and then looked for the reason it smoked and found that the blower motor was shorted (and stank horribly).
It was straighforward to replace, but when I put everything back, NOTHING worked at all - no lights on the control panel, nothing. I then checked the voltage across the terminals and saw 240V and was puzzled until saw that there was no 120V to neutral where the plug connected to the back of the stove. The outlet, however, had 120V to neutral. Since it was a molded plug I thought that was not likey to be a cmmon failure, so after killing th breaker I took off the outlet cover that the stove plugged into and found out that the neutral terminal was intermittent.
The neutral contacts were not grabbing the netral terminal on the plug tightly enough and were a little discolored in one spot. All that moving around of the plug while moving the stove probably moved it just enough not to work at all - that thing was a fire hazard that I'm surprised hadn't been the cause of more damage in a house only 12 years old. Rather than try and clean the termnals and trust bending them to be tighter (and worry about metal fatigue) I spent the $10 so that I could sleep better for a tight new 240V 30A outlet.
Everthing works like a charm now.

Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.

Just replaced the element and put new rock grate supports on the rock grates and we're set to grill

Remove burner knobs, Removed 7 screws from bottom of face plate. Removed screws from 2 alluminum or steel spacers I guess you could call them. I let the Op Panel hang carefully not to stress wires. I marked all wires of the Latch asm. Removed the four screws holding it in and carefully removed the wires. Replaced in opposite manner and self cleaning works. The oven tried to start the cycle but I noticed the latch never triggered. When the function first stopped working I was able to apply slight force to the door and the latch fired. So after replacing the door switch it still failed to work. So latch asm was the official fix. So I have had to replace the latch asm and the Op Panel for being dim. I don't think this model is very good. But Partselect.com is great easy to find parts and good prices. Very pleased with my experience.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select