S120 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from ALTADENA, CA
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Hinge on one side had snapped.
Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SCROGGINS, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Both door hinges was simply worn out from 20+ years of usage.
Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from central city, KY
- Parts Used:
- 12001311
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
blower motor
removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- S from Washington, DC
- Parts Used:
- WPY04100019
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
The bake element had burned out
Regrettably I have been unable to replace the bake element since the two screws are completely stuck. This doesn't appear to be a common problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary E from Oak Forest, IL
- Parts Used:
- WPY04100019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replace bake element
Unscrew the two screws. Pull the element out a few inches. Unclip the wires by pulling them apart. When we did this the wires retracted back into the opening. It was difficult to reach them and pull them back out. Be sure to hold the wires or clip something on them to hold them out till you can attach the new element. Attach the new element wires and screw the plate back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grady E from Vidalia, GA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed Replacement Filters
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sedro-Woolley, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lefrt Front Burner Quit Working
Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Monmouth, OR
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven door hinge
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lansdale, PA
- Parts Used:
- WPY04100019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom baking element burned out
Easy job. Anybody can do it. This replacement is accessed from inside the oven.
1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.
1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Eureka, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Any setting selected (1 thru 9) would result in the surface burner going to full hot
Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwen from COLUMBIA, SC
- Parts Used:
- 12200031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace unreadable knobs.
Was able to remove the older ones to replace with new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from SHELBYVILLE, TN
- Parts Used:
- WPY04100015, WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replaced broiler element
my Jenn-air stove is 32 yrs old. Its heave well made and works. I Didn't want to deal with researching to find new down draft that would not fit the same as old one. The Element was perfect solution..fast easy cheeper than new stove and installation bill!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BEND, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing.
Removed old filter and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Gastonia, NC
- Parts Used:
- 866294
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Range oven door switch need replaced
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top; and close lid. Part #866294
Was this instruction helpful to you?
Thank you for voting!