JGR8775RDW Jenn-Air Range - Instructions

I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!

There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.

Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

My Husband did the repair in less than an hour. He followed the way it was put together removed it the same way and replaced the whole unit very easily.

repair is very easy, just needed to push them in place

Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.

Nothing mechanical was required! But the service was phenomenal. These are just a drop in part. I was thrilled that you had them, received them in one day without overnight charges, And the cost was very reasonable.

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand.
I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly

ordered new broiler pan