S166 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- david from central city, KY
- Parts Used:
- 12001311
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
blower motor
removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ALTADENA, CA
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Hinge on one side had snapped.
Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Searcy, AR
- Parts Used:
- 12001311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Blower was stopped up and running extreme slow
Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.
Everything went fine. No trouble.
Everything went fine. No trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SCROGGINS, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Both door hinges was simply worn out from 20+ years of usage.
Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from SOUTH HOLLAND, IL
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven would not heat
First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Wilmington, DE
- Parts Used:
- 12200039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch for fan was heat damaged and broke
Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Chapel Hill, NC
- Parts Used:
- Y702615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic lens broken... pilot light not very visible
Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Mulkeytown, IL
- Parts Used:
- 703917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken temperature knob on my oven
This was obviously not a hard repair, I just replaced the knob. I would like to say that I did receive the part in just a little over 24 hours. That was nice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from York, PA
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill elemnt on ancient Jenn-Air died
Just replaced old with new, it plugs in same as old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Byron from LE SUEUR, MN
- Parts Used:
- WP74003387, 8009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb and socket became one when trying to remove a burned out bulb. Ruined the socket.
Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mohd fouad alahdab ruh from JAMAICA, NY
- Parts Used:
- WP74003387
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
The oven light went off, changing the bulb did’n’t solve the proble, beacause the socket was burned.
First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Pawtucket, RI
- Parts Used:
- Y703673
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After a lighting storm the oven would not work it kept blowing the range fuse it was determined by a friend it ws the selector switch
first removed the four screws that held the panel in place, tthen unscrewed the actual switch itself. I then pulled the wire, one at a time from the old switch and pluged the wire in to the new switch. upon completion I tested the oven selector switch and secured the switch in place, then replaced the panel. And I'm up and running again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Eureka, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Any setting selected (1 thru 9) would result in the surface burner going to full hot
Opened oven door, took four screws out of the front control panel, removed the two screws holding the burner control switch to the front panel, removed the wires from the old switch one at a time and installed them on the new switch. secured the new switch to the front panel, put the four screws back into the front panel, and closed the oven door. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!