IRP85800 Inglis Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LOUIS C from GRAND JCT, CO
- Parts Used:
- WP3149404
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dual burner would go to highn heat.
Watched video & did just guy in video did. Very easy job & the burner works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph K from PAHRUMP, NV
- Parts Used:
- WP3196548
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The oven light shorted out causing the safety thermostat to blow.
Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light
Works great again...without the light
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George E from OCALA, FL
- Parts Used:
- 3184020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
the fastener became loose and dropped into the stove
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from GREENBRIER, TN
- Parts Used:
- WP3148952
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilton from CANYON LAKE, TX
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven bake would not heat up at all.
Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!
NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- corey from SHAKER HEIGHTS, OH
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sparks flying out of the oven, broiler element melting
First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service call to the appliance repair guy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from LANCASTER, SC
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element had burned into
The video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from MIDDLETOWN, CT
- Parts Used:
- WPW10308477
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Old lower element fell apart
1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phillip from RUTH, NV
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
small inner burnner out
looked on internet on how to remove top. an easy fix after watching video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Clermont, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not reaching temperature
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from WATERVILLE, ME
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven stopped heating, error message stated heating element
Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominique from ASHLAND, MA
- Parts Used:
- W10823692
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dual inner element stopped working. The ceramic portion had a crack most likely from thermal stress over the years.
First I found a YouTube video for Maytag Range Repair – How to replace the Surface Element with Limiter - 6" - 1200W
The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge
2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.
3. Take a photo of the element being replaced for wiring connections.
4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both
5. The clips have to be removed from the old element and put on the new one. Place them in the same locations
6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element
7. Put everything back together in reverse order.
Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.
The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge
2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.
3. Take a photo of the element being replaced for wiring connections.
4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both
5. The clips have to be removed from the old element and put on the new one. Place them in the same locations
6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element
7. Put everything back together in reverse order.
Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Oklahoma City, OK
- Parts Used:
- 814381
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosalind from APOLLO, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the oven temperature was not working right. I installed a new oven sensor. Works get now
Watch the video...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from NORTH PORT, FL
- Parts Used:
- W10856603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element not working properly
Remove 2 screws inside oven holding element . Remove screws holding back panel. Plug wires (2) into new element.Install back panel . Done.
Was this instruction helpful to you?
Thank you for voting!