IGS325RQ1 Inglis Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from COLUMBUS, OH
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
very intermittent oven won't light. Can hear gas and spark but won't light when spark isn't at ignitor tip (shorting somewhere before the tip)
Remove;
Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out.
Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick.
Oven racks.
Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out.
Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove.
Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes.
Reverse to install new ignitor.
Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out.
Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick.
Oven racks.
Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out.
Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove.
Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes.
Reverse to install new ignitor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BURNSVILLE, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
This was an easy fix for a seventy year-old like me!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SAINT CLOUD, MN
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven sensor was not regulating heat set for oven
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patrick from HUGHESTOWN, PA
- Parts Used:
- WPW10181986
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
temp sensor went oven not heating
the hardest part was moving stove to trplace part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from PLUM CITY, WI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not keeping correct temp and sometimes would not relight when temp went dropped.t
Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruno from LE ROY, NY
- Parts Used:
- WP8523175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottom piece of range rusty
took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EDEN PRAIRIE, MN
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter stopped sparking.
I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!
Was this instruction helpful to you?
Thank you for voting!
Whirlpool gas stove burner igniter had broken.
Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat. I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from PT PLEASANT, NJ
- Parts Used:
- WP8273104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken knob
Replaced the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Maple Grove, MN
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Rear Drawer Glide
This was a very smooth repair. In total it took about 5 minutes. The pot drawer below the oven wasn't gliding like it once did. After I replaced the glides it works like new. Please note, if you are going to replace one side go the next step and replace both to provide balance to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from Punta Gorda, FL
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Paint peeling from strip
removed 3 screws holding the strip and replaced with new strip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from SAINT JOSEPH, MI
- Parts Used:
- WP9758079
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
WOULD NOT HOLD DESIRED BAKE TEMP
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from SAINT PETERS, MO
- Parts Used:
- WP9758079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Stove would not light due to faulty electronic ignighter
Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from WEST JORDAN, UT
- Parts Used:
- WPW10293048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven would not maintain Heating
Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.
Was this instruction helpful to you?
Thank you for voting!