Models > IES366RS1 > Instructions

IES366RS1 Inglis Range - Instructions

Jump to:

All Instructions for the IES366RS1
121 - 135 of 187
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Joseph from Channelview, TX
Parts Used:
WP9761958
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
R&r
Was this instruction helpful to you?
Thank you for voting!
Customer:
Beth from Draper, UT
Parts Used:
W10856603
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broiler element EXPLODED!
Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JoAnne from Harrison, AR
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven element burnt out
unscrew two screws..took old element out, put perfect fit new element in,screw two screws back in.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard from Brazoria, TX
Parts Used:
WP9761958
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Dover, NJ
Parts Used:
WP3148953
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
8 Inch electric burner not getting hot
I determined the problem by swapping the 8 inch burner with a 6 inch burner. the 8 inch got hot when connected to the 6 inch wire harness. This told me that the 8 inch burner was good. The 6 inch failed to get hot so I determined the next logical thing was the power to the 8 inch burner. I used a multi meter to determine that power was getting into the control unit but no voltage was getting out. The controller was bad. I ordered a new controller and after unplugging the stove, replaced the controller in about 10 minutes. (Critical part of repair is to unplug unit from wall -220 volts!)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from Titusville, FL
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Grant from Alexandria, VA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nick from Chapel Hill, NC
Parts Used:
W11597884
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken drawer handle
My son broke the drawer handle of our stove a few years ago. It took me a while to get this repaired because the first company we ordered from shipped the wrong product to us and did not allow us to do a return! The team at PartSelect had the correct product delivered in just a few days! Once I had the product on hand the repair was super easy. Thanks PartSelect for great service!! Nick, ShirtsThatGo
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rodney from Columbus, OH
Parts Used:
W10856603
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
broiler didn't work
Removed original broiler element, and found it was open. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eddie from Kaiser, MO
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
the heating element went out.
removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Wooster, OH
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ken from Las Cruces, NM
Parts Used:
WPW10181986
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven shutting off after temp reached 350
Remove the plug from outlet then shutoff gas. Remove the 10 screws hold the back panel of the oven. Unclip the connector of the temperature sensor from the main line. Pull the sensor straightout. Reverse the process install the new sensor. Couldn't be any easier. Oven working great. Calling in a reapairman would have cost $200 for parts and labor.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Billy Scott from Tupelo, MS
Parts Used:
WPW10308477
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The heating element had burned through from food spillage and sticking
I removed the broken heating element while waiting for the new part to arrive and cleaned the oven. SO much easier without anything in the way. Once the part arrived and it was wonderfully packaged...Easy to open but very well protected, it was a snap to connect the 2 power wires and then screw in the 2 screws to secure the heating element. I was back to baking in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from San Antonio, TX
Parts Used:
WP9761958
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .
Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Coral from Duluth, MN
Parts Used:
WP3148952
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken burner switch
Easy as pie! Thank you for the illustration to help us pick out the correct part.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the IES366RS1
121 - 135 of 187