IEP315RQ1 Inglis Range - Instructions

Needed new drip pans for range top. Easy fix. Was impressed on how quick the parts were shipped out to me.

I removed the broken heating element while waiting for the new part to arrive and cleaned the oven. SO much easier without anything in the way. Once the part arrived and it was wonderfully packaged...Easy to open but very well protected, it was a snap to connect the 2 power wires and then screw in the 2 screws to secure the heating element. I was back to baking in less than 10 minutes.

Went on line to see if the repair could be done by us. Watched repair video and from there on the repair went as smooth as it possibly could.

Yes... it exploded. Ordered the part which was delivered promptly. Installed in about 30 minutes with a helper. Just unscrew the 4 interior screws and a bunch of the screws (10 maybe?) on the back panel. Drop the back panel, remove the electrical connections from the broiler element and have your helper pull it out. Shove the new one in carefully through the insulation, attach the two electrical connections and reattach all the screws. Worked fine but smelled a bit as it burned off the new coating. About a 30 minute project.

Unpluged from electric. I took two bolts out of back of oven attached to boiler. Pulled out and exposed cords the attach to boiler. Slide them off and removed old boiler. Attached cords to new boiler and slide part back in to attach the two bolts back. Plugged oven back in and worked great

just replaced the broken glides with the new ones.

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

Keep in mind that I am a 65 year old woman who has replaced bake elements on a much older range that was hard wired. I viewed the video so I knew what to expect. The job would have taken no more than 15 minutes if the retaining screws had not been stuck. After several doses of WD40, I finally managed to get them loose but only then after I had tried every screw driver in the house. I clamped the leads with vise grips to keep them from slipping back in the stove. Unplugging the old broken element and plugging in the new one took maybe a couple of minutes. The retaining screws went back in without a problem.

removed the two screws and unhooked the old heating element. I set the new element in place and attached the electrical leads and replaced the two screws and tested the oven.

I took the old bowls out and dropped the new bowls in. No problem.

We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.

Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for being a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Only difficult because one heating element connector broken off. Before receiving correct part, tried to install generic element, which had leads about 2 inches too long, so trying to force into place bent electrical connectors that go from oven to heating element. Tried to bend one back and it broke off, so did not bend 2nd one back. Received correct heating element, and slid unbroken connector on one element side, and soldered 2nd element on. Screwed heating element in and it works fine.

Followed the easy instruction sheet provided.