RGB533CEH6CC Hotpoint Range - Instructions

Unbolted the old parts, cleaned the stove, and bolted the new parts on. Looks just like brand new!! The parts were perfect, easy to find, inexpensive, and delivered quickly!
Thank you!

repair was easy,couldn't believe I found parts. Bought house with stove in it.wife wanted new one,replaced broken parts cleaned up oven saved 600 bucks.

First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.

Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.

just slipped it in

Slid the oven door off of the hinges and laid it on a sheet on the kitchen island counter top. By simply looking at the spring clips on the new door gasket it was obvious how to use pliers to squeeze the clips on the broken gasket to easily remove it. I took the opportunity to clean the oven door before putting the new gasket on. Installing the new gasket was very easy, simply inserted the spring clips into the holes on the door and pushed until I heard the "click". Anyone can do this repair.

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

unplug power and turn off gas/// had to remove all star screws on top/remove ign wire from each burnner/now remove stove top/ adj wrench and remove nuts from the front nobs and relace with new front orifice tubes NOTE: Front orifice tube is the leftside. Front orifice HOLDER is the right side. put back top, open front to put hand in to make adjustments to ign wires close top and reinstall star screws and using finger to hold and make adjustments on top now turn power and gas on. I use soapwater to test for leaks/ leo gubin

nothing to it.

Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.

I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.

changed old burner tube , with new equipment. thanks to PartSelect.