RB525*P3 Hotpoint Range - Instructions

Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.

replace old one with new one thank you.

Ordered new element (super-easy to select the right one at this site!). Turned off stove breakers. Removed two screws holding mounting hinge plate with nutdriver. Detached wires with regular screwdriver. Attached wires to new element lugs with screwdriver, using furnished new screws. Reinstalled element hinged mounting plate with screws and nutdriver. Only difficulty is 1) working bent over inside the oven because the wires are short, and 2) wire screws are regular, not Philips, with shallow slots so screwdriver slips out frequently.

The old eye was lifted up, hinge screw removed, and three screws removed from the eye that connected lines to it. Did just opposite for installation. Very easy. The hardest problem was finding an eye with three screw-type connections.

The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.

My oven is so old that the model # tag has been scrubbed blank. I search your site by Brand name and oven description. I found the pictured element in your listing and sized it up. Part arrived as promised. It was simple to install - power down oven via circuit breaker and remove 4 ea screws and removed defective element. Install new element and reattach via screws. Turn on circuit breaker and power up oven to test - all working fine.

First, I turned off the power at the breaker box. Then, I removed the 2 screws attaching the bake element to the back wall of the oven. Next, I pulled the element out a few inches and removed the screws holding the element to the wires at the rear of the oven. Finally, I reattached the new element to the wires with the screws and then reattached the element plate to the rear wall of the oven. I turned the power back on at the breaker box, and tried the new element. It worked! Also, shipping was real fast, like 2 days from the time I placed the order to receiving the element.

removed the old element, inserted the new one.

It was easy and worth doing myself because a repairman said, he could do it for $50.00 dollars. I spent $28.00 which includes the shipping cost.

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

Simply removed two screws to detach element from oven wall, removed two terminal wires then reversed the procedure to install the new element.

1.Shut off power to stove. 2. Lift up non-working burner. 3. Unscrew retaining screw that allows burner to tilt. 4. Lift burner out. 5. remove clips from ceramic holder. 6. Unscrew 3 screws holding element, write down which color is attached to which element, or label wires. 7. unpack new element, directions say to cut off and tip the leads with solder, but I re-used the old circle connectors. 8. Screw the wires back on the new element (using nutdriver) 9. place element in new ceramic holder provided, and clamp shut. 10. place element in stove top opening and screw in retaining screw (honestly I could not get this to work correctly, so I just left the element sitting in the hole). 11. Turn power back on. This could take as few as 5-10 minutes, but I allowed 1/2 hour for turning power on and off or moving the stove to unplug it.

Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

I replaced the element. The new part arrived within 48 hours of being ordered. It worked. The part that sticks out the back of the oven with the connections was a little shorter on the new element which made it more difficult to put the wires on but it was not too difficult.