RJ7420J1 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Saint Louis, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bottom oven burner went out.
Removed two small bolt screws that held the bottom burner in place. Unscrew the two small screws that attach the oven wiring to the bottom burner. Put the bottom burner back in place and screw the two small bolt screws back in and its done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Southfield, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Broken heating element
Turned off electricity at fuse box. Unscrewed old element and removed. Put in new element, screwed it in. Turned on electricity. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tulsa, OK
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
top element in oven was broken ,not working
Removed 4 screws and removed the old element and replaced in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Venice, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace Burned-out oven bake element
Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- c from Cincinnati, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element melted! Lucky it didn't start a fire!
The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.
If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The element in the upper oven burned out. Looked like a welder's torch when it went out.
After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
My part was delivered in 2 days regular UPS.
The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Mena, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element brned out.
Removed two screws to release the burner, then two screws to disconnect the wiring and replace them. Then inserted the burner int position and replaced the two screws which were removed to remove the burner.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Pasadena, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke in several places
Turned off the power source to the oven. I then removed the two screws that hold the element in place, then pulled the element out about 3 inches and disconnected the two wires at the back. The hardest part was getting the screws turned to connect the new wires at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Marietta, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baking Element not working
Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felicia from Little Rock, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bottom heating element in the oven was not heating
First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out.
I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Flower Mound, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Beke Element broke into 3 pieces
followed the existing guidelines from this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Saint Louis, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old element burnt out.
No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Oceanside, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Coil element blew up breaking in three pieces.
I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Paducah, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element was burned out.
Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Was this instruction helpful to you?
Thank you for voting!