RB525*T1 Hotpoint Range - Instructions

I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pushed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put the old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires

removed it, ordered it and it only took 15 minutes to replace it.

I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.

Very quick delivery, within 3 days.

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

Took the broken heating element out of oven. Replaced with new one; which was easy to do.

Turned on oven. It started heating immediately

The repair seemed very easy, even before I attempted it. When I recieved my part it was very obvoius that this was my problem part. The old element was worn out(21 yrs old). Having Thanksgiving around the corner, my wife was happy we had a fix to our not ready to replace oven. I was very pleased with your website picture matching choices and the very fast shipping you offered.
Thank You RR from Massachusetts

My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.

First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service