RK966G307 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Silver Spring, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
My 20+ year old bake element cracked
I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Roseville, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace baking element
Turned off power at breaker and removed old element and replaced new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Millbrae, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Heating element corroded.
I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Carrollton, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench set
Heaty element broke in half
Our home was built in 1990 and has an original GE oven in it. When the bake element broke in half, I thought for sure it meant buying a new oven. When I looked on line and found Part Select.com, I was impressed to find the exact part I needed. I requested the part on Saturday, and it arrived on Tuesday. I installed the part on Saturday just in time for hosting our Super Bowl party and baking enchiladas! You guys saved the day! Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rand from San Mateo, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burned out lower heating element
Very simple 4 screws/nuts ...off on...done.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Gualala,Ca, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old burner had burned out and broken
removed old element and installed new, and oven is up and working like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Mena, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element brned out.
Removed two screws to release the burner, then two screws to disconnect the wiring and replace them. Then inserted the burner int position and replaced the two screws which were removed to remove the burner.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Very easy, however you will need a flashlight to see by since the back of the oven is rather dark.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Pasadena, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke in several places
Turned off the power source to the oven. I then removed the two screws that hold the element in place, then pulled the element out about 3 inches and disconnected the two wires at the back. The hardest part was getting the screws turned to connect the new wires at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Marietta, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baking Element not working
Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felicia from Little Rock, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bottom heating element in the oven was not heating
First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out.
I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Flower Mound, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Beke Element broke into 3 pieces
followed the existing guidelines from this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Saint Louis, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old element burnt out.
No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Oceanside, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Coil element blew up breaking in three pieces.
I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Paducah, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element was burned out.
Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Was this instruction helpful to you?
Thank you for voting!