RK7660T3 Hotpoint Range - Instructions

First I located the circut breaker to the oven- once no power supply was confirmed (oven light was out) I diconnected the screws that held the old element in place. Pulled the old element forward and disconnected them from the wires. The hardest part was getting onto the oven to reconnect the wires to the new element since the door opens down the work space is a little tight and awkward. Connected new element and replaced screws. Done in less than 20 minutes and no repair service calls to pay!

Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.

Turned off power to oven and removed screws attaching element to back of oven with a socket wrench. After removing the screws, I pulled element out about six inches and used a screw driver to remove the screws that attached the two electrical wires to the end prongs of the element. After removing old element, I simply reversed the process to install the new element.

I removed the two screws that held the element in place. I pulled out the element and disconnected the two wires and unscrewed the screws and then place the new element to it. screwed the wires back to the element wires and then push it back in. Replaced the outside plate and screw the two screws back in.

Save myself money by doing it myself.

turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set.

Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element from the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.

Piece of cake to repair. I took both both heating elements off. I sprayed oven cleaner everywhere to soften the grime. I waited 10 minutes and wiped up the softened baking grime. Installation took 5 minutes for each element and about 15 minutes to clean the oven while both elements were removed.

removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

I remove the back plate, pull out the wires, and unscrew the screws and put the new part. The problem that I had was reaching to the back of the oven to remove the screws. Other than that it was very simple.

The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.

Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.