107RF38-E Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nancy from Houston, TX
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner started sparking and burned right through the coil
Took the old part off and marked the wiring for easy replacing and looked all over town and no part to match, so I went to the Internet and put in 8" burner and luckily found your website. The part was perfect and saved me alot of time doing more research for the part. Thank you for the quick shipment and good correspondence.
I will definitely use you again for parts and tell my friends about your website too.
I will definitely use you again for parts and tell my friends about your website too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pierre from South Burlington, VT
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner element was blown
Remove the old element by removing one screw and inserted new element and replaced the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Cape May Court House, NJ
- Parts Used:
- WB30X356
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
elements were burned out
Removed the elements from the stove and disconnected the wires. Reconnected wires to the new elements and reinstalled in the stove. I was very impressed with the delivery time. I ordered online at 3:00 PM and the parts were at my door at 9:00 AM the next morning. Greatest service I ever had from anyone! I am 250 miles from the warehouse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from San Antonio, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from STREATOR, IL
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element was not heating
I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Bishop, CA
- Parts Used:
- WB2X5103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
worn out gasket
Used a putty knife and dental pick to remove old gasket remnants and installed new gasket with putty knife and thumb pressure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hubert from Oak Ridge, TN
- Parts Used:
- WB30X356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
A plastic bowl was placed on the hot eye and melted.
The old eye was lifted up, hinge screw removed, and three screws removed from the eye that connected lines to it. Did just opposite for installation. Very easy. The hardest problem was finding an eye with three screw-type connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from San Jose, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erbin from Poquoson, VA
- Parts Used:
- WB44X5043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element burned into.
TURN POWER TO OVEN OFF AT POWER PANEL 1- Remove element: 2 screws ... cut wire at element because of burned area. 2- Crimp two new wire lug connectors onto wire and attach to new element with supplied screws. 3- Attach element to back of oven: 2 screws ... TURN POWER ON AGAIN AND TEST OVEN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Beckley, WV
- Parts Used:
- WB30X354
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
one element suffered a small puncture where the heated element burned thru
The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tamaqua, PA
- Parts Used:
- WB30X356
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The burner only heated half of the coils
The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter J from Oceanside, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old stained drip bowls
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Yonkers, NY
- Parts Used:
- WB32X10013, WB32X10012, WB30X356, WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replace heating element on range top
Shut power to unit. Tilted burner element back, then removed pan screw,with nut driver which holds rear hinge in place. Next step was to remove clips that hold porcelain cover that covers the wires.Used nut driver to remove the three the wires. Installed new unit in the reversed order. Just make sure wires replaced in proper order. really easy !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Wild Rose, WI
- Parts Used:
- WB30X356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replace Non-working stovetop burner unit (electric)
1.Shut off power to stove. 2. Lift up non-working burner. 3. Unscrew retaining screw that allows burner to tilt. 4. Lift burner out. 5. remove clips from ceramic holder. 6. Unscrew 3 screws holding element, write down which color is attached to which element, or label wires. 7. unpack new element, directions say to cut off and tip the leads with solder, but I re-used the old circle connectors. 8. Screw the wires back on the new element (using nutdriver) 9. place element in new ceramic holder provided, and clamp shut. 10. place element in stove top opening and screw in retaining screw (honestly I could not get this to work correctly, so I just left the element sitting in the hole). 11. Turn power back on. This could take as few as 5-10 minutes, but I allowed 1/2 hour for turning power on and off or moving the stove to unplug it.
Was this instruction helpful to you?
Thank you for voting!