RB7372D3 Hotpoint Range - Instructions

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

The interesting part of this story was troubleshooting the problem. Was it the element or the control? Turns out the element was making poor contact, generating excess heat ,which corroded the element contact generating even more heat, and so on and so on until the termional block eventually broke. The repair itself was simple once I separated the element from the terminal block. After that I removed the terminal block, one screw, removed the connecting wires, two screws, reversed the procedure to install the the new terminal boplck and element. Before the whole process began I made sure to turn the breaker to OFF.

Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.

1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.

Ordered part, took old bake element out, installed new bake element. It was real easy.

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.

took cover off back of stove. Removed two screws and wires that were attached to the element. Removed old element and installed new element. An easy repair.

This range is about 30 years old and I was thrilled to still be able to get the bake element, which burned out about a month ago. I was doing research to buy a new stove when a cousin, from out of town, called to say they were going to visit the following week. No time now to get a new one installed. "partselect.com" was the fastest way. THANK YOU!

First off, I want you to know I'm an obese 56-year female without tools. But, I knew where to borrow those.

I first shut the power off to the range. I then disconnected the 2 screws that hold the element and pulled it out to reveal the 2 screws which connected the wires. I unscrewed those and removed the bake element. I double checked the stove model and bake element part # at the GE website and ordered it from "Partselect.com". It came in about 3 days. I then reversed the order of the above and it was done.

Here are some challenges I encountered..
1) The oven door was in the way making it uncomfortabe to get to the back of the stove.
2) Those $#%& screws are so short I kept dropping them.
3) The wires in the back bend easily. Be careful.

That's about it. It was a pill but not a real problem. It sure beat buying a new range before I've decided on which one to buy.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Drilled out the screw on one wire as it was corroded to the metal socket. Sanded both wire terminations. Installed wires into terminal block. Reassembled all loose parts and installed into burner slot. Worked perfectly.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.