RC777*03 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond ` from Houston, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broiler electrical heating element burn-out.
Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Corpus Christi, TX
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing burner element
I bought the replacement element for my 98-year-old aunt, and she installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from San Francisco, CA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner needed replacing
Just plugged it in! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mission Viejo, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Broiler Element Burned Out
The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Pagosa Springs, CO
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had burned out-needed replacement
Plugged it in. It fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert R from Richmond, MO
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a burned out calrod unit
Simply unplugged the burned out one and plugged in the new one. It worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ella from Tampa, FL
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pre 1992 6" plug in electric cooking elements- rusted out
Worked, don't have to replace an old GE combination range "Microwave Cooking Center" when the surface units rusted out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, MA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element failed
lift up to 45 degree angle and pull towards you. This one went bad and the contacts welded themselves together. Took some shifting and tugging to free it. Normally, they slide in and out effortlessly, like any plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Warren, NJ
- Parts Used:
- WB44X196
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven bake element burned out.
Replaced old bake element by removing two screws holding it to back of oven. Disconnected old bake element from lead wires by removing two other screws. Installed new bake element by reversing the process. Only issue is that the tabs on the element that connect to the leads are easily bent and you need to use vise-grips to keep from bending them. Otherwise, very easy. Thank you PartSelect.com for stocking this item that I used to repair my 45-year old GE range!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Cortlandt Manor, NY
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not keep heat
pulled out the old one pushed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Ellettsville, IN
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element burned out
From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!
Was this instruction helpful to you?
Thank you for voting!