RF431R3 Hotpoint Range - Instructions

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

the replacement items fit really good. It was a matter of remove and replace,

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the metal correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfectly.

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.

Because of the age of the oven it took a little time to loosen the screws that held the element in. Once the screws were removed it was a matter of pulling the element out about 3 inches and disconnected the two wires, then it was a matter of repeating the steps in reverse. Very quick and easy

First I shut off the range breaker in the main electrical panel. I slid the oven door off for easy access to the back of the oven. I loosened the two hex head screws holding the element to the oven wall. I pulled the element forward to reveal the two hex head screws holding the wires to the element and removed the old element. I attached the wires to the new element with the hex head screws, fastened the element to the oven wall, slid the oven door back on, and flipped on the breaker. I gathered up my tools and left the apartment. It took me longer to get to the apartment and back than it did to do the repair. PartSelect.com got the part to me within two days of my order, and for six dollars in shipping that's great.. PartSelect.com has been added to my internet bookmark.

This was quite an easy fix once I got the correct part. It was my own fault for ordering what I thought went with my oven. I didn't expect to be able to even find a new heating element because the stove is almost 40 years old. Except for that one part it works just fine. It took me about 20 minutes to do the repair. I unplugged the stove, unscrewed the 2 screws holding the element to the back of the stove, pulled it out far enough to unscrew the 2 screws attached to the wires, screwed the new part to the wires, screwed the whole unit back onto the back of the stove and plugged it back in. It works great. Moving the stove away from the wall was more difficult than installing the new part. It couldn't have been easier and it was a lot less expensive than buying a new stove. Also, the customer service people I spoke to were very friendly and helpful and there was no problem returning the incorrect part. I would recommend this company to anyone who asks.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

Oven unit went well and is working. Tilt burner unit was wrong and did not fit. Needs to be replaced by 8 inch tilt burner with four input.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.