RC548*01 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Fenton, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Lower Baking Element burned out - needed replacement.
Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Apple River, IL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element broke
Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TOM from SAMMAMISH, WA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven Would Not Heat
Replaced lower element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Riverside, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was bad, no heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.
I was glad they had the part for such an old oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Canyon Country, CA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element wouldn't heat
Just pull out the current element and plug-in the new one. Part was received in 24 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Roanoke, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
Same as you described
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reynolds Station, KY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat
Removed the oven shelves. Removed two small screws in back of oven. Gently pulled out element to get to two other small screws connecting the element and removed them. Removed old element. Placed new element in oven connected the two screws to the element. Replaced two screws on back of oven. Replaced the shelves. That's all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlin from Nampa, ID
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven was not heating the way it should of done.
I double checked to make sure I got the right part.I looked at your video and then just did as you suggested. It was a easy fifteen minute job. Thank you for making this so simple to follow along with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Brookfield, WI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
lower ( bake) element burned out
Turn off breaker for unit! Use nut driver to remove old element,and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Leesburg, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element did not work
Once I watched the video pertaining to the installation of the part, the job was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Warr Acres, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The bottom heating element was not working
This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Raleigh, NC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element in oven had broken
It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Inverness, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat in oven, Only broiler working
Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ida from Ann Arbor, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
lower over burner did not heat.
I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hampton, IA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
oven element stopped working
It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!
Was this instruction helpful to you?
Thank you for voting!