RK962G4K2 Hotpoint Range - Instructions

Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after reconnecting the new element the broiler tested OK. It is once again broiling steak to perfection

Replacing the electric oven element was easy. It took about 20 minutes and all you need is a screwdriver and a pair of pliers. What you have to do first, turn the power to the oven OFF. Remove the original element carefully observing how
it was installed and install the new element in the same order.
I have used Parts Select a couple of times in the past years and the delivery came quicly without any problems.

Spyro.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

My Husband did the repair while I wasn't home. He didn't bother to shut off the power even though he should have. He didn't electicute himself or burn down the house and the oven works great so I guess it was a success!

First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!