RB6360T2AD Hotpoint Range - Instructions

Before ordering the new part, made sure the problem was the burner and not the wiring in this very old stove by putting an ohmmeter on the terminals of the burner after removing it. Since it showed no conductivity, the burner was bad (could have put the voltmeter on the wires and turned on the power to ensure power was coming in......but did not want to mess with 240 volt/high amperage. With power off at the breaker, installed new burner. One caution... since the wire on the burner terminals is pretty soft, don't bend them by putting too much torque on the screws. This turned out to be my only problem.....I had to clean up the screws and work them through the copper terminals with the burner outside the oven before attempting to screw them on the wire connectors in the oven. Not a big problem, but if you bend the terminals too much when you install the burner in the oven, you run the risk of shorting them together, or breaking one. And that would be a big problem.

I first unplugged the stove as that was easier than going to turn off the breaker. I removed both oven racks for more room to work. There were two screws to removed inside the back of the oven. After pulling the element out a few inches I was able to unscrew the two screws that held the wires onto the element. I made sure to note which wire went on which side. Then did everything backwards with the replacement element.Plug the oven back in and make sure it works. This was the easiest repair I have ever had to make on any appliance! It's good to note the new element could heat much faster and hotter than the old one. I plan to check the temp when baking. The replacement one also hinged so cleaning in the future will be much easier as well.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

Removed the screws. Pulled out the element and disconnected the wires. Attached the wires from the new heating element and screwed it in.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Oven unit went well and is working. Tilt burner unit was wrong and did not fit. Needs to be replaced by 8 inch tilt burner with four input.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

I was lucky to look at other repair stories because I forgot to turn off the power!!! Nothing happen to me, but it was as simple as everybody else said. Unscrew the two screws, pull out element, unscrew another two screws and put back together in reverse order. Viola, the oven was back in working order just in time for a major event the next day. Thanks everybody for their tips and partselect for fast shipping.

I turned off the breaker, removed two screws that held the element in place, pulled it out about four inches, disconnected the screws securing the wires to the element. Removed the old element, placed the new one in the oven and reversed the procedure.